F11 Error

Frigidaire Gallery Range F11 Error

Troubleshooting and Repair - F11 Error Code - FPCS3085LFB

Frigidaire Gallery Range F11 Error is a shorted key error. It means when a key on the keypad has been detected as pressed in for a long time the F11 error is reported and  all oven commands are terminated.

First simply press the cancel key to clear the code. The error may have been caused by just holding down a key too long by mistake. If the error persists you will need to replace the keypad or keyboard (membrane). On these particular models the keypad is built into the console so the entire assembly has to be replaced. The console assembly with the keypad membrane can be found at the page linked below.

Click Here For Part And Ordering Information For The Keypad Membrane

If replacing the keypad membrane fails to remedy the problem then the EOC (Electronic Oven Control) will have to be replaced also. The information for that part is below.

Click Here For Part And Ordering Information For The EOC

In order to access and replace either part you will need to remove the control console. See the page linked below for instructions to do that.

Click Here For Instructions To Remove The Control Panel Console

This Frigidaire Gallery Range F11 error troubleshooting and repair information applies to model FPCS3085LFB and all the models listed under the related models section below.

Frigidaire Gallery Range FPCS3085LFB
Questions For Error Code F11

F11 Error

We have had this house about 4 years but we were remodeling it, we heard the F11 alarm going off and we couldn’t get it to clear so we just flipped the breaker. We’re about done with remodel so we thought we would take a look at oven. Try to find a reset button or whatever. The F1- error just beeps and beeps. No other buttons will do anything at all, no clear, no nothing. But beeping so we flipped the breaker back off. Model # FFEW2725LBB SER.# NF14421173. Thank you

If you are getting the F11 error and killing and restoring power to the unti does not help then the control panel will need to be replaced. If you are getting the F1 error then the main control board is the problem. The F11 error means the keypad is shorted which is why the control panel has to be replace to fix it.

 

How to Reset Frigidaire Gallery Range.

Information board on front of stove went out with a power surge and the burners work but nothing else. Is there are a reset button or something else I can do?

The only thing you can do is try and reset the electronics by killing power to it at the breaker/fuse panel on your home for one full minute then restore power. If after that the problem persists the control was damaged from the power surge and it will need to be replaced. If you want the part information just post a new question with your full model number and I will look up the part number for you.

How Replace

How do we fix or replace part. We have shut off the breaker for an extended time, turned back on still same error.

The page linked below has instructions to replace the control board.

https://www.appliancecodes.com/repairs/how-to-access-and-replace-electronic-oven-control-eoc-part-number-316560143-on-a-frigidaire-gallery-slide-in-range/

F11 Err For Model Cgef3034mfd; Serial# Vf25169319

Similar to cases already listed my stove started “beep talking by itself”. I'm the only person in the house so no one could have set the timer or push buttons. Even after I pressed “Cancel“ button it stopped for awhile only to come back again - with or without displaying F11 ERR code. I unplugged the stove overnight, plugged it back the next day just to have the same problem re-appear. None of the commands on the panel are functional- timer, clock, oven, self clean…. However, buttons and cooktop plates are working. I just bought the place and do not know how old appliances are. However, they look new. Model CGEF3034MFD; serial# VF25169319. Please, advise! Thank you!

You will need to replace the main control as it has failed. The part you need is part number 5304495520. You may find it on eBay or Amazon or you can just google that part number and you will find plenty of places to order it from online.

 

F11 Err On Fridgedair Oven

Constant beeping showing f11 err Model FGGF3058RF gas free standing

F11 on the frigidaire gas range means there is a shorted keypad or selector switch on the main control. All you can do is first try and reset the electronics by killing power to it at the breaker/fuse panel on your home for one full minute then restore power. If after that the problem persists:

1. Check/reseat ribbon harness connections on the EOC.

3. Replace the EOC.

The part number for the EOC which is the main control board is Range Oven Control Board 316560118, however, it's out of stock everywhere so it may be hard to find one. 

F11 Code

In the middle of the night I heard my timer beeping on my stove. While beeping it was showing an F11 error code. I'm the only person in the house so no one could have set the timer or push buttons. The stove will be 2 years old on March 6, 2021 and hoping nothing is going bad on it. Frigidaire FGEF3036TB Serial number is VF90316882.

The only thing you can do is try and reset the electronics by killing power to it at the breaker/fuse panel on your home for one full minute then restore power. If after that the problem persists the user interface control board will have to be replaced. The F11 error on that model means there is a stuck key on the panel. The part number for the control you would need to replace is 5304511270. Hopefully, it will just reset and you won't have any more trouble. 

F011 Err

How to fix the fo11 err on a wall oven, FGEW2766UFA

The F011 error on that model means the following:
Stuck key: a key that has been detected has pressed continuously for 30 seconds or more. 

1. If a key was pressed inadvertently for a long time this error code will be displayed. Make sure there is nothing (water, utensils) in contact with the keyboard. The fault code should go away once the key is released and the Stop key is pressed. If the F011 error comes back when a key is pressed it means the error condition is still there. If the F011 error does not come back it means the error condition is gone and the oven can be used.

2. If the fault code cannot be cleared, test the wiring harness between the oven user interface board (connector I2C1 or I2C2) and the touch panel (connector I2C1 or I2C2).

3. If the fault code cannot be cleared and the wiring is good, the touch panel is most likely defective: replace the touch panel.

4. If changing the touch panel did not fix the problem replace the oven user interface board.

The part numbers for the touch panel are based on color:

Part #5304514975 - stainless

Part #5304514976 - black

The control board part number is 316474948

Hope this information helps.

F11 Err

Hello! Can somebody help us to tell what we have to do if the Frigidaire has a signal and f11 err noticed and everything we do, we can’t make it shutting off.. if is possible to call us 7809155549. Thank you!

The F11 error on that model is a stuck key error. 

1. Verify nothing is touching the potentiometer/display boards. Disconnect Power, wait 30 seconds and repower.

If fault returns: 2.Check/reseat connectors and harnesses between ESEC-UIB and potentiometer/display boards;

3. Replace ESEC-UIB;

4. Replace potentiometer/display boards.

Ask A Question
Ask a question about the F11 error

Have a question about this error code?
Fill out the form and a certified appliance technician will answer your question usually within 24 hours. You will be notified by email once your question is answered. Questions not related to this error will not be answered. Find the error you need help with in our database. If it's not in our database submit it on our code info request page.

Related Frigidaire Gallery Range Models
This F11 error code also applies to the following models
CPCS3085LFA
CPCS3085LFB
FPCS3085LFA
FPCS3085LFB
FPCS3085LFC
FPES3085KFA
FPES3085KFB
FPES3085KFC
FPES3085KFD
FPES3085KFE
FPES3085KFF
FPES3085KFG