F28 Error

Whirlpool Duet Dryer F28 Error

Troubleshooting and Repair - F28 Error Code - WED8300SW0

The F28 error means the moisture sensor strip is open. Which means it's most likely bad. This error can also be caused by the sensor circuit in the main control board, but is not very common so replace the moisture sensor and if the problem continues you know the board is at fault. The moisture sensor is the two metal sensor strips on the face of the lint screen housing.

Click Here To Order Moisture Sensor Strip

This Whirlpool Duet Dryer F28 error troubleshooting and repair information applies to model WED8300SW0 and all the models listed under the related models section below.

Whirlpool Duet Dryer WED8300SW0
Questions For Error Code F28

F28 Code.

How do I fix this F28 code? Model WED6400SG1

First unplug the washer for a full 2 minutes then plug it back in and try to start a cycle if you still get the same codes after that you need to replace the interface boards. The boards you need for that model are linked below.

Click here to order the interface board.

F28 Code

I’ve read all the questions and answers but above it says it has 2 sensors. Does the part above have 2 sensors or just one? Will I need to order 1 or 2?

I can't answer any model specific questions like that without your model number. I will need the model number repost your question and include your full model number, thanks.

Cabrio dryer code F28 & F2

My dryer recently threw a F28 code. I replaced the moisture sensor but this did not fix the problem. After reading the answer from Michael Crum’s question above, I replaced the control board. After hooking up the new control board it’s now throwing a F2 code. Should I have replaced the user interface board?

Yes, you have a stuck key on the interface board that is what the F2 error is anyhow. If the error is not resetting then yes the interface board is the issue. Sounds to me like both boards failed on the unit.

F28 error code

I have Whirlpool Cabrio dryer model WGD7300XWO. I got the f28 error code and ordered a new moisture sensor bar. After removing the front panel I noticed there were 2 strips. I replaced the top one with no luck, then replaced the bottom one. The bars don't appear to be corroded or covered in material to prevent contact. My dryer is still giving me an f28 error and flashing "sending". I'm stuck here. Any help would be appreciated.

Check the wiring harness connections between the moisture sensor and the main electronic control board, if the wiring looks good and there are not any loose connections and you already replaced the moisture sensors then the main board has failed. The control you need to replace can be ordered from the link below:

Click Here To See Part and Ordering Information For The Main Electronic Control

Cabrio dryer code f28

The dryer threw a code f28. I took a damp cloth and wiped the sensor by the lent intake. The dryer switched from sensing to wet on the control panel but the dryer still doesn’t come on. What’s my next step?

The F28 error on the cabrio models also means the moisture sensor is open, which means it's probably bad. However if the sensor is good then the sensor circuit on the main board has failed. Very unlikely problem so I would just go ahead and replace the moisture sensor first if that does not fix the problem then you will need to replace the control board. If you need part information or technical troubleshooting info resubmit your question and include your dryer's model number and I can give you more information.

Ask A Question
Ask a question about the F28 error

Have a question about this error code?
Fill out the form and a certified appliance technician will answer your question usually within 24 hours. You will be notified by email once your question is answered. Questions not related to this error will not be answered. Find the error you need help with in our database. If it's not in our database submit it on our code info request page.

Related Whirlpool Duet Dryer Models
This F28 error code also applies to the following models