Can you give me the part number for the thermal fuse for model number WED8300SW2 ?
Whirlpool Duet Dryer F01 Error Repair Instructions
The Whirlpool Duet Dryer F01 error may be able to be fixed with a simple reset of the main control. Unplug the dryer for 1 minute and plug it back in this will reset the control if the error persists after that you will need to check the dryer thermal fuse. The fuse is located on top of the blower wheel housing. In most cases its not the fuse causing the F01 error code but it's worth checking because in some rare cases it can be and it's a $20.00 part VS a $200.00 part.
To check the thermal fuse remove the bottom access panel off the front of the dryer and you will see the fuse mounted at the top of the blower wheel housing. (See Image Below) Remove the two wires and check the fuse for continuity, it should be closed. If it does not have continuity it's bad and that is likely the problem.
If the fuse checks out to be good then the main control board will need to be replaced to fix the F01 error. To replace the main control you will need to remove the top off the dryer, there are a few screws on the very back of the dryer lid that hold it in place, remove those and the dryer top will slide back and lift off. Once you have the top off , standing at the front of the dryer on the left side of the cabinet towards the top you will see board mounted to the control bracket, remove the bracket and unplug the wires going to the board. Make sure to take a picture of the wiring before disconnecting them so you do not forget where the wires connect to the board. Then install the new board.The control board or fuse can be ordered from the links below.
Electronic Control Board
Dryer Thermal Fuse
Can you give me the part number for the thermal fuse for model number WED8300SW2 ?
The part number for model WED8300SW2 is WP3392519 you can order it from the link below.
I cannot find the listing for my Duet model WED9200SQ1. I was wanting to order the control board or thermal fuse.
Do you sell the main boards for a whirlpool dryer with a model number WED9450WW0? It displayed an F01 error code and the main board was found burnt as is common. Thanks
The control board you need to order for dryer model WED9450WW0 can be purchased on amazon at the link below:
Need to know what model number control board to order for wed8300sw0 duet sport F1 Error
The control you need to order can be ordered from the link below:
I can’t find the above model on your site. Apparently F01 has to do with the control board or thermal fuse needing replaced. Can you help with the part numbers?
The control board for that model and the thermal fuse can be ordered from the links below:
Thermal Fuse & Control Board Part Information for dryer model number # WED9500TW1 Dryer.
The thermal fuse and control board for dryer model number # WED9500TW1 can be found at the links below.
Model WED9400sw1. Need help with repair to fuse or control board?
You need to check the thermal fuse with a meter, if the fuse has a closed circuit it's good and the board is bad. If it has an open circuit the fuse is bad. It's rarely the fuse that causes that error code though, it's almost always the board. The board for you model is linked below:
Click here to order control board
If you know how to solder and have soldering tools then you can just buy the repair kit for the board, the correct kit for your board is linked below:
Click here to order the repair kit
If you need any further help visit our free live chat at any of our sites:
Just tried starting my Duet dryer. F 01 came on. I’ve unpluged for one minute. No luck. Can you assist?
That means the main control board has failed. If you need part info come to the site chat and give me your model number I will be glad to help you that.
got a code F1. I turned off the power for 5 minutes to see if that would reset. It didn't. So I think I need to replace the circuit board. Or should I buy a new dryer?
You would be correct you do need to replace the dryer control board. If you would like the part information for your model open a new question and give me the full model number of the dryer. The model number is located on a tag on the frame of the dryer behind the dryer door. Open the door and you will see a tag with the model and serial number on the frame.
Need control board for model WED9200SQ0 please...
The board you need for your model can be purchased from the link below:
They are expensive so if you know how to solder you may be better off just buying the repair kit for the board. It's linked below:
Model# WED8300SW2 Thanks!
The control board you need for the model you posted is linked below:
https://prismparts.com/products/oem-whirlpool-dryer-electronic-control-board-pp2805106?_pos=2&_sid=76048735b&_ss=r
Can you please reference the control board for my dryer? Model #WED8410SW1
The control you need for that model is linked below:
https://prismparts.com/products/oem-whirlpool-dryer-electronic-control-board-pp2805106?_pos=1&_sid=b295e0e38&_ss=r
Duet dryer WED9200SQ1. Went to start dryer it made a clicking noise along with a buzz and an definitive electrical burn smell. I have tried to reset by unplugging , but it only then buzzes a few seconds when pushing start. It then makes a click at the control panel board and displays the flashing f01 signal. Would a new control panel board solve this issue. Thank you
Yes, you would need to replace the control board. The part you need can be ordered from the link below:
https://prismparts.com/products/whirlpool-dryer-main-electronic-control-board-pp6826106?_pos=1&_sid=94d53876d&_ss=r
Can you please reference the control board for my dryer? Model #WED8410SW1
The control board you need for that model is linked below:
https://prismparts.com/products/oem-whirlpool-dryer-electronic-control-board-pp2805106?_pos=1&_sid=013804ca8&_ss=r
Can you please reference the control board for my dryer? Model #WED8410SW1
The control board you need for that model can be ordered from the link below:
https://prismparts.com/products/oem-whirlpool-dryer-electronic-control-board-pp2805106?_pos=1&_sid=50c662499&_ss=r
WGD9200SQ1
You would need to replace the main control to fix that error. The control you need can be ordered from the link below:
https://prismparts.com/products/whirlpool-dryer-main-electronic-control-board-pp6826106?_pos=1&_sid=bd61cdd84&_ss=r
Serial number MU3014931. I keep receiving the page can’t be found.
The control you need for the model you listed can be ordered from the link below:
https://prismparts.com/products/whirlpool-dryer-main-electronic-control-board-pp2605106?_pos=1&_sid=fe6fc71e6&_ss=r
Could you please give me the part number and price to purchase a new control board please
The control board you would need for that model can be purchased at the link provided below. The page will have all the information including price of the board.
https://prismparts.com/products/whirlpool-dryer-main-electronic-control-board-pp6826106
Can you tell me the part number of my whirlpool front load duet model number WED9400SWO electronic control board
The control board you need for model WED9400SW0 can be ordered from the link below:
Hello, I have a Whirlpool Steam Duet dryer, model #: WED9600TA1. It was running fine for 6 loads throughout the day. Then I went to start it with my final load, when I pushed the start button, it made a clicking noise and would not initiate drying cycle. I unplugged for a few minutes, plugged back in and tried it again. Same response. Before I spend money on a repairman, I'd like to know what it could possibly be and if it's even worth repairing as I've had for 15-16 years. Thank you.
Yes it is repairable. The F01 error code is a internal failure code of the main control board and it will need to be replaced. The control board you need for that model is linked below:
Instructions to replace it can be found on the page linked below:
http://www.appliancecodes.com/repairs/how-to-fix-whirlpool-duet-dryer-f01-error/
WED9470WW1 have already replaced the fuse a couple months ago.
The F01 error means the main board has failed and it will need to be replaced to fix the dryer. The board you need for the model you listed is linked below.
If you Have a question about this repair fill out the form and a certified appliance technician will answer your question usually within 24 hours. You will be notified by email once your question is answered. Questions not related to this repair will not be answered. Find the error you need help with in our database. If it's not in our database submit it on our code info request page.